internal wiring ms1 v3 - vw abf engine 60-2 wheel

N' spark, EDIS etc

internal wiring ms1 v3 - vw abf engine 60-2 wheel

Postby mbaye » Mon Dec 21, 2009 6:09 am

high all happy to see a vw megasquirt forum
my name is Mbaye from senegal west africa i'm runing vw abf engine 60-2 whell wasted spark 4 bmw coils 2 modules 0227 100 200 from peugeot in my actual internal wiring xg1 and xg2 are jumpered tachselect to optoin ; optoout to tsel
pullup 1k to 5 V proto area r26 to ign spark A r29 to spr4 spark B
is my wiring correct cause i see in a post the xg1-xg2 jump is cut
thanks
Random avatar
mbaye
 
Posts: 7
Joined: Sat Dec 05, 2009 3:04 pm

Re: internal wiring ms1 v3

Postby prof315 » Mon Dec 21, 2009 8:03 am

Based on what you are describing you are set up for a hall type rpm input. You need to set things up for VR input. http://www.megamanual.com/index.html go to step 50 for instructions.
User avatar
prof315
 
Posts: 59
Joined: Tue Dec 08, 2009 7:33 am
Location: Melbourne, FL

Re: internal wiring ms1 v3

Postby mbaye » Mon Dec 21, 2009 10:06 am

the crank sensor got 3 wires i think for vr sensor you have only 2 wires
actualy the engine start and idle well can you please explain how can i do
thanks
Random avatar
mbaye
 
Posts: 7
Joined: Sat Dec 05, 2009 3:04 pm

Re: internal wiring ms1 v3

Postby prof315 » Mon Dec 21, 2009 4:04 pm

Actually most VW crank sensors have 3 wires: Sensor +, sensor-, and shield (goes to engine ground) I'm not sure about the ABF but I know that the ABA, AEG, AWW,AWP et all use a 3 wire VR sensor pinned as I described.
User avatar
prof315
 
Posts: 59
Joined: Tue Dec 08, 2009 7:33 am
Location: Melbourne, FL

Re: internal wiring ms1 v3

Postby mbaye » Tue Dec 22, 2009 2:30 am

yes i know for the ABA but on the ABF sensor 3 pins there is no shield it's black + brown groud and white /blue midle wire is the signal going to ms but anyway can you confirm me about xg1 and xg2 jump or cut i can show you a picture of the sensor if you want
thanks
Mbaye
Random avatar
mbaye
 
Posts: 7
Joined: Sat Dec 05, 2009 3:04 pm

Re: internal wiring ms1 v3

Postby prof315 » Tue Dec 22, 2009 5:34 am

If your sensor is in fact a hall type then you will want to keep xg1 and xg2 jumpered. Is there power going to the sensor on any of the pins?
User avatar
prof315
 
Posts: 59
Joined: Tue Dec 08, 2009 7:33 am
Location: Melbourne, FL

Re: internal wiring ms1 v3

Postby mbaye » Tue Dec 22, 2009 5:53 am

yes there is a power 12 volt on the sensor the engine is european vw golf 3 2l 16 v 150 hp year 93
Random avatar
mbaye
 
Posts: 7
Joined: Sat Dec 05, 2009 3:04 pm

Re: internal wiring ms1 v3

Postby prof315 » Tue Dec 22, 2009 12:39 pm

You shouild be good to go then
User avatar
prof315
 
Posts: 59
Joined: Tue Dec 08, 2009 7:33 am
Location: Melbourne, FL

Re: internal wiring ms1 v3

Postby mbaye » Tue Dec 22, 2009 1:17 pm

thanks for your reply prof
now all what i need is a fine tuning for race engine is stock
gsxr itb alpha n 250 cc injectors
wasted spark with 4 bmw coils one coil per cylinder
2 bosh modules 0227 100 200
one of these module can drive two coils
any help would be apreciate
thanks
Random avatar
mbaye
 
Posts: 7
Joined: Sat Dec 05, 2009 3:04 pm

Re: internal wiring ms1 v3 - vw abf engine 60-2 wheel

Postby prof315 » Wed Dec 23, 2009 5:44 am

upload your msq and let me see....
User avatar
prof315
 
Posts: 59
Joined: Tue Dec 08, 2009 7:33 am
Location: Melbourne, FL

Next

Return to Ignition

cron
Hosted by Freeforum.ca, get your free forum now! TOS | Support Forums | Report a violation
buying traffic website
MultiForums powered by echoPHP phpBB MultiForums